12332358 - Laserfiche WebLink

Home Browse Search

Onsite Permit 555-24-004158-PRMT Page 2 of 3 Schedule or track inspections at www.buildingpermits.oregon.gov Call or text the word "schedule"to 1-888-299-2821 use IVR Number:555050077780 y Schedule using the Oregon ePermitting Inspection App,search"epermitting"in the app store ! a'•W.� *% C" - i4., � N,:,., ' .o g 3'�b §C" 5 J, <•:r '�' �b H L3 eY 'R�I�n'. 17a a issti ,6'124 i :� � r 7 r �€ -, p ration bate ! 4'12 '4. 4 �„£ •P. w � , ey -_;. '"z 'ftitork descrrptiian A:I =�R I;�AACE FAILING S ,ORt3EPR SFp ti ,„ Media type: Other-Indicate Product/Manufacturer Media depth: N/A Media type description: EZ-Flow Trench length: 375 linear ft. Rock above pipe: N/A Max depth: 14 in. Undisturbed soil between trenches: 8 ft. Min depth: 12 in. Capping fills-min depth of fill material: 16 in. Special Requirements Stake out required: Yes Groundwater type: Temporary Groundwater depth: 20 in. Pump to drainfield reqd: Yes Filter fabric on top of drain media: N/A Conditions of approval -Capping fill rules at OAR 340-071-0265.Construction must occur in dry soil conditions between June 1 and October 1 unless otherwise approved by the agent.The cap material must be pre-approved by the agent prior to placement.Minimum 10-ft between edge of fill and trench.Drainfield area must be scarified.Contact between native soil and fill must be mixed.Final cap to be seeded and or landscaped to prevent erosion. Protect from livestock and vehicular traffic. Serial distribution.The cap material must be evenly graded to a final depth of 16-inches over the drain media. •Dry soil installation only(June 1 —October 1 unless otherwise authorized by the agent). •The system must be installed by the property owner or a licensed sewage disposal business (installer). -Vehicular traffic and livestock must be restricted from the system area. •All roof drains must be directed away from the system -All tanks must be tested for watertightness and have a water-tight riser to the ground surface.Twenty-inch minimum diameter if less than 36-in deep.Thirty-inch minimum diameter if greater than 36-in deep. Maintain access to septic tank for pumping and service. -Meet all required setbacks -The system must be installed in the area approved during the site evaluation and in accordance with the construction plan approved by the agent, including any changes made by the agent. •All work is to conform to OAR 340, Division 71 and 73. Make no changes in system location or specifications without approval by the agent. •For product approval information and manufacturer installation requirements see DEQ website at: http://www.oregon.gov/deq/Residential/Pages/Onsite.aspx •The pump and alarm must be wired on separate circuits in the control panel. Pump wiring must comply with applicable building,electrical,or other codes.An electrical permit and inspection from the Department of Consumer and Business Services,Building Codes Division,or the municipality with jurisdiction, is required for pump wiring installation. •Install the pump and system components in accordance with the approved pump curve and specifications. •An anti-buoyancy device is required for the septic tank(s)and must be installed as per the manufacturer installation guidelines. •A minimum 18-gauge,green-jacketed tracer wire or green color-coded metallic tape must be placed on top of the effluent sewer or pressure transport pipe from tank to drainfield. -Header pipe from Distribution or Drop Box must be minimum 4-ft length,level,and bedded. •Each drainfield trench must be level within a tolerance of plus or minus 1-inch. -Maximum length of an individual trench is 150-feet. -Serial distribution,each trench bottom to be level and on contour. Use Drop box(es). 6/24/24:8:42:55AM ONS_OnsitePermit_pr