Laserfiche WebLink
! ( : ; , , ELECTRICAL SHOCK HAZARD ! i _ , EXPLOSION OR FIRE HAZARD <br /> LIit Disconnect power before instating or servicing this Do not use this product with flammable liquids. <br /> product.A qualified service person must install and � `'{ ,r y. Do not install in hazardous locations as defined by <br /> service this product according to applicable electrical `r I d, National Electrical Code,ANSI/NFPA 70. <br /> and plumbing codes. <br /> Failure to follow these precautions could result in serious injury or death.Replace product immediately if switch cable becomes damaged <br /> or severed. Keep these instructions with warranty after installation.This product must be installed in accordance with National Electric Code,ANSI/ <br /> NFPA 70 so as to prevent moisture from entering or accumulating within boxes,conduit bodies,fittings,float housing,or cable. <br /> For detailed specifications on this product, or for the complete line of SJE-Rhombus® <br /> panel, alarm,and switch products, visit our web-site at www.sjerhombus.com. <br /> INSTALLING THE FLOAT SWITCH Figure A <br /> i <br /> 1. Place the cord into the clamp as shown in Figure A. <br /> 2. Locate the clamp at the desired activation level and secure the <br /> clamp to the discharge pipe as shown in see Figure A. <br /> Note: Do not install cord under hose clamp. �lcJi h u 111 `- ` <br /> 3. Tighten the hose clamp using a screwdriver. Over tightening II,4kap <br /> may result in damage to the plastic clamp. Make sure the float 3.5 inch(9 cm) <br /> cable is not allowed to touch the excess hose clamp band during tether length <br /> operation. <br /> 4. Wire cable leads directly into control device as shown in Figures <br /> B&C. <br /> 5. Check installation.Allow system to cycle to insure proper Figure B -TAXI Standard <br /> operation. Note:All hose clamp components are made of 18-8 <br /> stainless steel material. See your SJE-Rhombus®supplier for nreplacements. <br /> INSTALLING THE ALARM c <br /> 1. Mount alarm box using existing holes in back of box.To ensure II n O <br /> water-tight seal, use screws and sealing washers included with `� �l o 0 <br /> alarm. Note: Screws are to be located over wall stud or used with C't,,'' 'tOBt <br /> !2-float <br /> a wall anchor sized for a#8 x 1.25 self tapping screw. III i r^ neutral <br /> 2. Determine"conduit-in"locations on alarm as shown in Figures B V 1)Il I14-line <br /> to of <br /> &C. Note:When used with a pump application, connect alarm (Irci,____ra)) !ground <br /> to a circuit separate from the pump circuit.This allows alarm to <br /> continue to operate if the pump circuit fails. °` 0 G <br /> 3. Drill holes for conduit entry,taking care not to damage bosses `` JJ <br /> inside alarm box. recommended recommended <br /> power condua Itoal switch <br /> 4. Attach conduit. inlocallon conduo;n <br /> location <br /> If alarm includes premounted terminal block option,refer now Incoming wire size 14-22 Awg <br /> to the Terminal Block Option Wiring Instructions. <br /> 5. Bring float switch cable through conduit and wire to terminal Figure C-TART with Auxiliary Contacts <br /> block positions 1 and 2 as shown in Figures B&C. optional auxiliary <br /> 6. Wire power conductors to terminal block positions 3 and 4 and contacts connection <br /> ground wire to ground termination post as shown in Figures B& (see wire labelin-. \ <br /> C. Note: If terminal block option is used, attach ground wire as ��� <br /> shown in Figure A of Terminal Block Option Wiring Instructions. o/', to` C .° I <br /> 6.0 <br /> 7. If remote device is used, connect wires as shown in Figure C (,',It o IIo,. -- -� <br /> using supplied wire nuts. 1 o- o I of <br /> 8. Attach alarm box cover using the four pre-installed screws. 1 Ic It-float <br /> 9. Turn on power. Light on switch should come on. I I I I loca12-float <br /> 1 _neutral <br /> 10. Check installation by manually tipping the float.The horn and o o -- 4-Ilne <br /> beacon should turn on. l°°i <br /> 11. Push silence switch to test silence feature. a\,,,,1i ground <br /> 12. Test unit once per week to insure proper operation. G` O G <br /> recommended recommended <br /> power conduit float switch <br /> in location conduit in <br /> location <br /> Incoming wire size 14-22 Awg <br /> Si i- / ' hombus <br /> 22650 County Highway 6 • P.O.Box 1708 • Detroit Lakes,Minnesota 56502 USA <br /> 1-888-DIAL-SJE(1-888-342-5753) • Phone:218-847-1317 • Fax: 218-847-4617 • E-mail:sje@sjerhombus.com <br /> Instl.Instr.PN 1024984C Model TAXT ®SJE-Rhombus 08/12 <br />