|
•
<br /> 1M-1060 General Specifications and Illustrations
<br /> LIFTING STRAP LIFTING LUG —RISER CONNKTION
<br /> (TYPICAL) (4 TOTAL) (TYPICAL)
<br /> The IM-1060 is an injection molded two piece mid-seamii 'rr r.�
<br /> plastic tank.The lM 1060 injection molded plastic design y�II �� �`,
<br /> allows for a mid-seam joint that has precise dimensions A yr1� '�+�•! ` tI t l:�� 77:1111,\,,
<br /> nfor accepting an;engineered EPDM gasket:Infiltrator s 1 r 0% {� Ej °o ,asket desi n utilizes technolo from the water indust jl"-' " �'. °9 9 gY ► o d' ),s2ani
<br /> to deliver proven-means of maintaining a watertight.seal, ,t3 oiligep ry. fl i t �: � tl� EXTERIOR
<br /> The two-piece design is permanentlyfastened usinga III-
<br /> E si1
<br /> series of non-corrosive plastic alignment dowels and � � ^�� I �� �7
<br /> locking.seam clips.Tlie IM-1060 is assembled and sold r'i` "�"�`�`~ .JtiL..iw.raew i.ai��,ii�.lt ,
<br /> through a network of certified Infiltrator distributors. 127Af)2263EXTERIOR LENGTH
<br /> Must be backfilled and installed in accordance with TOP VIEW
<br /> Infiltrator Water Technologies,Infiltrator IM-Series Septic OUTLET
<br /> Tank General Installation instructions and for shallow
<br /> ground water conditions reference the Infiltrator IM- •Series Tank Buoyancy Control Guidance. T r � — d— t I c
<br /> �+ 54.7
<br /> Please visit www.infiltratorwater.comiimages/pdf/ "__o_ o - - n3Rq)
<br /> ManuatsGuides/TANK01-pdf for the latest information. HEIGHT
<br /> -t� r ��T EXTEWOR
<br /> SEAM CUP
<br /> ',�i�1tN,1♦II(
<br /> .1M4060 �z"' LIFTING STRAP 1 11111� i e�
<br /> Working Capacity 1094 gal(4141 L) (TYPICAL)
<br /> Total Capacity 1287 gal(4872 L) END VIEW
<br /> Airspace 16.5%
<br /> Length 127"(3226 mm) aid MI 024,s101 ACCESS OPENINGS WITH LOCKING LIDS(2)
<br /> PVCORASS ©4,102]PVC OR
<br /> Width 62.2"(1580 mm) W (2c
<br /> INLET -10.2 WA)FREEBOARD ABS OUTLET TEE
<br /> dyi---■sr— ....,in,-
<br /> iii
<br /> Length-to-Width Ratio 23 to 1 l�s�
<br /> I , AIRSPACE OUTLET
<br /> Height 54.7"(1389 mm) CO E t 6 1
<br /> 1 I PE I
<br /> CODE
<br /> Liquid Level 44"(1118 mm) ,I 44.0 i l 1
<br /> FIBERGLASS ; (111A) FIBERGLASS
<br /> Invert Drop 3"(76 mm) SUPPORT ! LIQUID SUPPORT
<br /> (TYPICAL) i DEPTH (TYPICAL)
<br /> Fiberglass SupportsI
<br /> WITH BAFFLE
<br /> 2
<br /> WALLWIiFRE
<br /> REQUIRED
<br /> Compartments 1 or 2 n._..._........._...._.�{.
<br /> Maximum Burial Depth 48"(1219 mm) SIDE VIEW
<br /> Minimum Burial Depth '6"(152 mm)
<br /> Maximum Pipe Diameter 6"(152 mm) TANKTOR CONTINUOUS
<br /> 320 lbs(145 kg) r-s, HALF' GASKET
<br /> STATE CERTIFI111 Environmental Health Special OR SEAM CLIP
<br /> ,�'''k jj
<br /> • EH -10 0 540
<br /> _ IG E
<br /> �~ ' M ✓�� L*--
<br /> TANK BOTTOM
<br /> s ''" HALF
<br /> -' 4 Ekrsiness Park Road
<br /> � M1
<br /> P.O.Sox768 obert Goodwin
<br /> Old Saybrook,CT 06475 ---- �
<br /> INFILTRATOR
<br /> ,. ?LT ..�. 1 804 221-4A35 U/660.577-7000•Fax.860-57T-7t101 - 7 tG%p )....' MID-HEIGHT SEAM SECTION
<br /> water technologic www:infiltratorswatercom
<br /> U.S Paten :4.759,661;5,017,041;5,156.488;5,336,017;5,401.116;5,401,453;5,511.903:5.716.163;5,586,778;5,839.844 Canadian Patents 1,329,959,2,004,554 Other patents penc0r g.infiltrator,E quartrar
<br /> Ouick4,and SideSMader are registered trademarks of Infiltrator Water Technologies.Infiltrator Is a registered'traden ark in Franca Infiltrator Water Technologies is a registered trademark in Mexico,
<br /> o.
<br /> Contour,Microl each'+ng,PolyTuif,ChamberSpa er,MultiPort,Pollock,OuickCut,QutckPlay.Snaptock and Straighttook are trademarks of Infiltrator WaterTertinologes.
<br /> PotyLok is a b,.leicark of Polytok,Inc.TUF-TiTE is a registered trademark of TUF TiIE,INC.Ultra-FFb is a trademark of IPEX Inc.
<br /> 43 2016InEltrator Water Tecfmologtes;LLC.All rights re.,erved.Printed in U.S.A. IM02 1116
<br /> Contact Infiltrator Water Technologies' Technical Services Department for assistance at 1-800-221-4436
<br />
|