Permit - 1271097 - Laserfiche WebLink

Home Browse Search

20. 22. 23. 24. 25. 26. 27. Porches, balconies or raised floor surfaces located more than 30 in. above the floor or grade shall have guardrails not less than 36 in. in Required guardrails shall have intermediate rails or ornamen- tal closures which will not allow passage of an object 6 in. or more in diameter. 214.2 Smoke detectors shall be installed outside of each separate sleeping area in the immediate vicinity of the bedrooms and on each additional story of the dwelling including basements. In dwelling units with split levels, a smoke detector need be installed only on the upper level, provided the lower level is less than one full story below the upper level, except that if there is a door between levels then a detector is required on each level. All detectors shall be connected to a sounding device or other detectors to provide, when actuated, an alarm which will be audible in all sleeping areas. R-215.1 In new construction, required smoke detectors shall receive their primary power from the building wiring. Smoke detec- tors may be battery operated when installed in existing buildings. R-215.2 Firestopping shall be provided in the following locations: in concealed spaces of stud walls at the ceiling, floors,soffits, drop ceilings, between stair stringers and at openings around vents, pipes, ducts, chimneys and fireplaces at ceiling and floor spaces. 402.7 Foundation cripple walls shall be framed of studs with a min. length of 14 in. or shall be framed of solid blocking. R- 402.9 The area within the foundation walls shall have all vegeta- tion, top soil and foreign material removed. R-603.2 Rafters shall be nailed to ceiling joists to form a con- tinuous tie between exterior walls where joist are parallel to the rafters. Where not parallel, rafters shall be tied with a rafter tie, located at or near the plate as practical. Rafter ties shall be spaced not more than 4 feet on center. Ridge board shall be at least 1 inch nominal thickness and not 28. less in deptt% than the cut of the rafter. At al! valley~ and hips there shall be a valley or hip rafter not less than 2 in. nominal chicknes~ and not less in depth %hah cut end of the rafter. When the roof pitch ~s than 3 in 12, members support- ing rafters and ceiling 3©itt, such as ridge beams, h~p~' valleys, shall be des~gnel! beams. R-702.3 Wood trusses shall be des~igned in accordance wit~ approved engineering practice. Trusse%~ shall be braced acccrd~:-~c their appropriate engineered design. Truss members s?~ll not b~ cu~ or a~%ered so designed. R-702.9 All plywood, when designed ~o be exposed in outdoor appllca- tions shall be of an exterior type, except that plywood roof sheathing exposed to the underside may be of inter,or type with exterior glue. R- 703.1 Provide screened with a net free area of' of the attic area (or 1/300 half is along eaves and thc other half in %he upper portion). R-707 A readily accessible access framed opening not less than 22 in. by 30 in. shall be provided. R-708 33. 34. Fireplace and chimney co;.:- struction shall conform to chapter 9. INSULATION REQUIREMENTS: Buildings with high-efficiency heating equipment shall be insulated as follow: ceiling R-30 (roof/ceiling assemblies in which has a slope of 3 ~n 12 or greater, may be R-19), walls R-11, underfloors R-19, other heating systems, ceiling R-38 (vaulted ceiling R-19} walls R-19 and under floor R- 19. 35. Elements of appliances which create a glow, spark or flame shall be located a min. of 18 in. above garage floor. M- 1114 36. Appliances subject to mechani- cal damage shall be guarded by a protective barrier. M-ill4