12983376 - Laserfiche WebLink

Home Browse Search

SPEC v SHEET WATERPROOFING 07 13 00 _'-- I^ Grace Construction Products (-4 degrees C) hand.Wet conditioner wit ball up under the fir- (25 mm) of base of wall. Treat the inside • Apply Bituthene 3003 Membrane thy in dry gertips. Let dry until conditioner cannot be corner by installing a 3/4" (19 mm)fillet of weather when air and surface temperatures rubbed off. If conditioned areas are not BHuthene liquid Membrane. Extend liquid are above 40 degrees F(5 degrees C) covered that day,recordtion the area 2 there membrane at least 3' (75 mm) onto wall • Bituthene Low Temperature Membrane is sigiflcant dust a dirt contamination membrane can be used at temperatures above Rimer • Option 2 - Treat the inside corner by 25 degrees F (-4 degrees C) and up to Apply &Fulton Rimer WP-3000 by spray or installing a 3/4" (19 mm)fillet of Bituthene 60 degrees F(16 degrees C) roller at a coverage rate of 500 -603 ff'/gal Liquid Membrane.Apply 12"(300 mm)wide • Cover the membrane immediately in tem- (12- 15 m2/L).Allow to dry 1 hour a until con- strip of membrane centered over fillet. peratures above 77 degrees F(25 degrees crate return to*trial cola. Apply wall membrane over inside corner C)to reduce potential fa blistering Apply Bituthene Rimer B2 by Iamb's wool and extend 6"(150 mm)onto footing.Aptly • Apply Bituthene System 4000 Surface roller at a coverage rate of 2E0-350 fly/gal(6 1' (25 mm) wide troweling of Biluthene Conditioner and other accessary Products -8 m2/L).Allow primer to dry 1 hour a edit tack- Mastic or Bituthene Liquid Membrane over not listed below in dry weather above free.Dry time may he longer in cold tempera- all terminations and seams within 12' 25 degrees F(-4 degrees C) toes (300 mm)of corner • Apply Bituthene Primer WP-3000 in dry Repfime areas if contaminated by dust.If At footings were the elevation of the floor weather above 40 degrees F(5 degrees C) the work area is duty, apply membrane as slobs 6'05)mm)or more above the footing, • Do not apply products to frozen concrete soon as the primers dry. Beat the inside corner either by one of the AFP(JC/VOON Surfaces treated with Deck Rep Suface above methods or terminate the membrane Surtax Cmdttiaer Treatment do not require conditioning or prim at the base of the wall.Seal the termination Bituthene System 4000 Surfrre Conditioner is ing.Metal does not require priming but must with Bituthene Mastic or Bituthene liquid supplied ready to use.Do not date wtth water be deaf dry and free of loose pant,oat a Membrane. or solvents.Spray surface corddioner uniformly otter c ntaminn rts.Use Bituthene Rimer B2 for At plaza deck-to-wall inside corners: to substrate at a rate of 300 fly/gal (7,5 m'/L), damp or green substrates. Do not apply • Option 1 - Apply membrane on wall and sesWe approprwte sprayer and nozzle. primer or surface conditioner to membrane, deck to withn 1"(25 cam) of corner.Treat PJkrw surface conditioner to dry completely Corners the inside corner by installing a 3/4" and thoroughly poor to membrane application. The treatment of cones varies depending on (19 mm)fillet of Bituthene Lquid Membrane, 1te surface c ndhuer is considered dry when the location of the corner. Extend Bituthene Liquid Membrane at least the substrate return to its original cola.To test 3' (75 mm) oRo deck membrane and 3" for dryness, rub small condtioed area by At wall-to-footing inside corners: • Opton 1 - Apply membrane to withn 1' (75 cam) onto wall membrane. Terminate TABLE 1 PHYSICAL PROPOt8E5 OF BIMHENE MEMBRANES Property&Test Method Wheat System 4000 Membrane BiMhene 3000 membrve Bituthene Law Temperature Membrane Oda Gray-black Dark gay-Uock Gray-black Ttwicres&ASIM D3767,Method A D060'(15 mm)nominal 01350'(IS mm)nominal 0060'(IS mm)nominal Low temperatse fte%IUNy.ASIM D1923 Unaffected at-4&F(-43Q Unaffected at-25'F(37Q unaffected at-45'F(d3`Q Resistance to hydrostatic head ATM n5385 237(A m)nin 200(60 m)min 237(61 m)ran Lap abeam al commas appicotan temperature. 50 bat(890 N/m) 40 INh(700 N/m) 50Iban(8(I N/m) width ASIM 01876.Mudfed Tecate strerglh membrane,AS1M D412(Die Q. 325 psi(2240 kPa)corn 325 psi(2243 Kb) it 325 pa(224014b)an Modified Tensile strength film ASIM D882 Modified 5000 pa(345 At )min 5000 psi(34S NEb)min 5000 psi(34.5 MPa)rrin Elongation ultimate failure of nbberted asphalt, 300%con 300%min 900%min ASIM D412 Modified Clacking tiding lm cycles.ASIM D836 Unaffected at-25`F(-32C) Unaffected at-25'F(-3M Unaffected at-2SF(-32°C) Noel strength yndttt ASTM D903.Modified 90 ban(1576 N/m) 901b/n(1576 Nan) 90 bat(1576 N/m) Rnclure resistance.n.m brans ASIM E154 50 Ib(222 N)nin 50 b(222N)rm 50 lb(222 N)mib 4.1.•-brnw..e,mmrimm AS1M E96 Water Method d 005 pa (2.9 ng/(FU x s x m)) OAS perms(29 rg/(Fb x s x m17) 005 Pans(2.9 ng/(FI x s x alp Water absorption,72tx,ASIM D570 0,l%max a1%may 0.rx max 44/ awma ,..1•ur"kw.°ry....,we.n.......w.0 m.n! 2•0 1.,Pe ie.,._I wau•x r.....•,In«a..r..x..4.u.k /J Peed