Laserfiche WebLink
This International standard was developed in accordance with internationally recognized principles on standardization established in tire Decision on Principles for IV <br /> l • Development of International Standards,Guides and Recommendations issued by the World Blade Organization Technical Barriers to Trade(TET)Committee. <br /> • <br /> • <br /> Designation: F1346-91 (Reapproved 2018) <br /> agill/ • <br /> INTERNATIONAL <br /> Standard Performance Specification for <br /> Safety Covers and Labeling Requirements for All Covers for <br /> Swimming Pools, Spas and Hot Tubs1 <br /> This standard is issued under the fixed designation F1346;the number immediately following the designation indicates the year of <br /> original adoption or,in the case of revision,the year of Last revision.A number in parentheses indicates the year of last ceapproval.A <br /> superscript epsilon(e)indicates an editorial change since he last revision or reapproved. <br /> 1. Scope 3. Terminology <br /> 1.1 This specification establishes requirements for safety 3.1 Definitions of Terms Specific to This Standard: <br /> covers for swimming pools, spas, hot tubs, and wading pools 3,1.1 appurtenances—subordinate parts or adjunct acces- <br /> (hereinafter referred to as pools, unless otherwise specified). sory components to the cover such as hardware including <br /> When correctly installed and used in accordance with the buckles, straps, ties, springs, anchors, tracks, rollers, lifting <br /> manufacturer's instructions, this specification is intended to arms, and the like. • _ <br /> reduce the risk of drowning by inhibiting the access of children <br /> under five years of age to the water. 3.1.2 automatic cover—a cover which can be placed over <br /> the water area and removed with a motorized mechanism <br /> 1.2 This specification includes performance tests to demon- actuated by a suitable control mechanism. See also power <br /> strate the compliance or noncompliance to requirements herein safety cover(PSC), other cover(OC). <br /> stated for safety covers.-It also includes marking requirements <br /> for all covers. 3.1.3 barrier—something that restrains or obstructs access <br /> to the body of water. <br /> 1.3 The values stated in inch-pound units are to be regarded <br /> as the standard. The values in parentheses are given for <br /> 3.1.4 blanket—a material used for thermal insulation. See <br /> information only. also solar energy blanket. <br /> 1.4 The following safety hazards caveat pertains only to the 3.1.5 cover—something that covers, protects or shelters, or <br /> test methods section, Section 9, of this specification: This a combination thereof, a swimming pool, spa, or hot tub. <br /> standard does not purport to address all of the safety concerns, 3.1.6 debris cover—a cover with attendant appurtenances <br /> if any, associated with its use.It is the responsibility of the user positioned over the pool area which permits the cover to <br /> of this standard to establish appropriate safety, health, and prevent debris, such as foliage, dirt, windblown trash, and the <br /> environmental practices and determine the applicability of like from entering the pool. It is intended to be completely <br /> regulatory limitations prior to use. - removed before the entry of bathers. See also other covers <br /> 1.5 This international standard was developed in actor- (OC). <br /> dance with internationally recognized principles on standard-. 3.1.7 decks—those areas abutting a pool,spa,or hot tub that <br /> ization established in the Decision on Principles for the are specifically constructed or installed(for example,of wood, <br /> Development of International Standards, Guides and Recom concrete, brick, stone, and the like) for use by bathers for <br /> mendations issued by the World Trade Organization Technical sitting, standing or walking and may also act as a base for <br /> Barriers to Trade (TBT) Committee. supports for covers. <br /> 2. Referenced Documents 3.1.8 dome—a semipermanent enclosure supported by <br /> trusses, or positive air pressure erected over the pool area to <br /> 2.1 NFPA Document: provide temperature and atmospheric control over the pool <br /> National Electridal Code,Article 680-262 environment. <br /> 3.1.9 energy conservation—the reduction of heat loss from <br /> pool water through air convection or evaporative cooling, or <br /> This specification is under the jurisdiction of ASTM Committee F15 on both. <br /> Consumer Produdts and is the direct responsibility of Subcommittee F15.28 on <br /> Covers for Pools,Spas and Hot Tubs. 3.1.10 hot tub—a spa constructed of wood with sides and <br /> current edition approved Feb. 1, 2018. Published February 2018. Originally bottoms formed separately; and the whole shape joined to- <br /> approved in 1991.Last previous edition approved in 2010 as F1346-91 (2010). gether by pressure from surrounding hoops, bands or rods; as <br /> DOI':10.1520/F1346-91R18. <br /> a Available from National Fire Protection Assoc., Batterymach Pare,Quincy, distinct from spa units formed of plastic, concrete, metal, or <br /> MA 02269. other materials. - <br /> Copyright©ASThM International,100 Barr Harbor Bdw,PO Box 0700,Wesl Conshohocken.PA 1992B-2959.United States li <br /> Copyright by ASTM Intl(all rights reserved),Thu May 3 I 1 15:07 EDT 2018 l <br /> Dovmloaded/pnnted by <br /> Paul Moore(Emerald Outdoor Living)pursuant to License Agreement No further reproductions authorized. <br />