My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
Permit - 1280171
Images9
>
Public Works - Permits
>
Building
>
FOR PUBLIC VIEW ON INTERNET
>
COMPLETED FILES - INACTIVE
>
92-XXXXX
>
Permit - 1280171
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
6/3/2010 3:17:11 PM
Creation date
9/3/2003 2:12:06 PM
Metadata
Fields
Template:
Permits
Permit Address
11661 STEINKAMP RD SE
Permit City
Aumsville
Permit Number
92-02535
Parcel Number
081W28C 02100
Permit Type
Permit
Permit Doc Type
Permit Document
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
40
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
Show annotations
View images
View plain text
11661 steinkamp Rd. S. E., Aumsville <br />August 11, 1992 <br /> <br />10. <br /> <br />11. <br /> <br />12, <br /> <br />13, <br /> <br />Individual glased areas in hazardous locations shall pass the test <br />(C~SC 16-CFR) requirements of section R-208.3 (safety glazing), <br />Hazardous locations are considered as follows: <br /> <br />a. In doors end within 12 inches of a door. <br />b. Fixed and sliding panels of sliding-type ~oo~s (patio type). <br /> <br />Wood framed walls less than four feet in width at garage door openings <br />shall be provided with approved hold-down anchors. Anchors arq to be <br />provided at each end of each wall segment and connect the wall studding <br />to the concrete foundation. As an alternate, a designed stsuctural <br />system to resist the requised 80 mile per hour wind load can be <br />provided. <br /> <br />Provide screened attic vents with a net free area of 1/150 of the attic <br />area (or 1/300 if half is along eaves and the other half in the upper <br />portion). (R-707) <br /> <br />ROOf trusses are required to be designed by an Oregon registered <br />Engineer or Architect. For trusses manufactured by an approved <br />fabrication plant, have the design and layout drawings available at the <br />construction site for the framing inspection. All job site cutting or <br />modification of the roof trusses shall be clearly shown in the <br />engineer's design calculations and drawings. <br /> <br />Listed appliances shall be installed in accordance with their listing <br />and the manufacturer's instructions. Factory built chimneys shall <br />conform to the conditions of their listing and the manufacturer's <br />instructions. (R-902) <br /> <br />INSULATION REQUIREMENTS: <br /> <br />Window class <br />Doors, other than main entry <br />Main entry door, max. 24 sq. ft, <br />Skylight class <br /> <br />U=0.40 <br />U~0.20 <br /> <br />U=0.50 <br /> <br />Approval as a result of this plan review or an inspection shall not be <br />construed to be an approval of a violation of the provisions of the dwelling <br />code Or of other ordinances of the jurisdiction. Reviews or inspections <br />presuming to give authority to violate or cancel the provisions of the <br />dwelling code or of other ordinances of the jurisdiction shall not be valid. <br /> <br />"APPROVED" only when this sheet is attached to plans <br /> <br /> <br />
The URL can be used to link to this page
Your browser does not support the video tag.